Camera Slider Card

Hey Crafters! "Wow" your friends with this great interactive card!  
Grab your Free template at the KoalaTCrafts Store today. Click  HERE to get yours. 

Supplies:

FREE TEMPLATE HERE

PINK CARD STOCK - http://amzn.to/2tg7Jky
BLACK CARD STOCK - http://amzn.to/2rzwNQ5
NEENAH WHITE CARD STOCK - http://amzn.to/2u21a1w
GREY CARD STOCK - http://amzn.to/2sV2u76
DECORATIVE PAPER - http://amzn.to/2u170QM
PAPER TRIMMER - http://amzn.to/2tgicMQ
SCISSORS - http://amzn.to/2shwqw3
ADHESIVE OF CHOICE ~

ALEENE'S TACKY GLUE  http://amzn.to/2ssYtpu 

GLUE BOTTLES -https://goo.gl/kUyE6r 

SCOTCH ATG GUN - http://amzn.to/2rqskk9

ATG TAPE - https://goo.gl/kUyE6r 

CORNER ROUNDER - http://amzn.to/2sbqUvN
FOAM TAPE - Double_sided_FOAM_tape.html
WHITE GEL PEN -Signo_Uniball_White_Gel_Pen_.html
STICKLES - http://amzn.to/2ubhWuS
MAYMAY MADE IT STAMPS - “Action” and “Oh Snap”
   Action Stamp Set

   Oh Snap Stamp Set
*Optional: You can use Punches instead of tracing the template
2 IN. CIRCLE PUNCH - http://amzn.to/2tgsdd7
½ IN. CIRCLE PUNCH - http://amzn.to/2tgsdd7
1 ½ IN. CIRCLE PUNCH - http://amzn.to/2tgsdd7

1 INCH SQUARE PUNCH - http://amzn.to/2tgsdd7

Let's get started! 

I'll show you how step by step in this video tutorial 

Scroll down for Measurements and Instructions.   

Instructions: 

1. Print your Template. Please note: the banner & white flash is not included in the template.

2. Cut out all your pieces of the camera, set aside.

3. Cut your White card stock to 4 1/2 x 11 for A2 card base.

4. Cut your one of your decorative papers  4 x 51/4" for your background it will be at 1/4" smaller than your card base (I used the light green). Adhere to your card base.

5. Trace and cut your camera piece onto pink card stock. +Tip - turn your camera over and trace so your lines don't show.   Set aside.

6. Trace and cut your squares (they measure 1"x 1"), thin strips (they measure 1/4") and the tiny flash from white card stock. +Tip - you can use a 1" square punch if you have one. You can use your template to trace the flash and cut just inside the traced lines.    Set aside.

7. Trace and cut Slider from black card stock. + Tip - place your template in the corner of your black card stock and trace only 2 on the sides and cut.  Also to create the little tab of the slider I traced the flash part of the camera and cut the small corners. - See video.  Set aside.

8. Trace and Cut the large circle (measures 2") on black card stock. +Tip - you can use a 2" circle punch if you have one. Set aside.

9. Trace and Cut the smaller circle (measures 11/2") on gray card stock. +Tip - you can use a 11/2" circle punch if you have one. Set aside.

10. Cut your second piece of pattern paper 1 1/4" wide. Making sure it's longer than your camera front. This will be for the front of your camera.

Now that we're done tracing and cutting we can put our camera together. +Tip - Always do a "dry run" no adhesive to make sure everything fits and is straight. I like to use a little bit of wet adhesive on the small strips to attach them to the camera front. Then I use my glue runner for the pattern paper. If you want to add decorative line do it now before you adhere the rest of your pieces.

Then, adhere your small white squares to the black strip making sure to leave some space between the squares. Then, flip your pink camera over place the slider on the top. Using it as a guide, put foam adhesive top, bottom and end leaving about 1/8" space around the slider. Creating a little channel for your slider to move in & out. Remove the backing paper from the adhesive and place your camera on your card base. You can now put the slider into the slot!

Put foam adhesive on the black circle and place it on the front of the camera. Using a white gel pen make a highlight on the gray circle. Then, put some foam adhesive on the back and center on black circle. Nice camera lens!

Now, to create the banner, I used a Maymay Made It Stamp set. +Tip - stamp in a corner of white card stock leaving a bit of room for a fishtail. It's easy and it will be straight. Use the trimmer to cut it out. To create fishtail cut a small slit in the middle of the piece of the sentiment card stock then cut from the corner to the middle. Repeat on other side. You should have a little V shape.  For the "pull" on the slider I used  another Maymay Made It Stamp set, VersaMark ink, and heat set white embossing powder. 

Finishing touches, I used a fine tip black pen to add stitch marks to my banner. This is optional. You can decorate your camera slider card how ever you would like. The possibilities are endless!

For details, see video HERE

Share your Camera Slider Cards with the KoalaTCrafts community on Facebook!  It is a fun group of crafters offering support and inspiration in a no commitment, no drama atmosphere.  facebook.com/

 
***VISIT ME ON SOCIAL MEDIA!!*** 

PINTEREST - pinterest.com/koalatcrafts
TWITTER - twitter.com/koalatcrafts
FACEBOOK - facebook.com/koalatcraft 
  INSTAGRAM - instagram.com/koalatcrafts
    PATREON - Patreon.com/koalatcrafts 

Discount adhesives and other supplies available
at www.koalatcrafts.com/store/

"I can't wait to see you next video!"

XOXO

Jen

AFFILIATE DISCLOSURE:

When I need certain supplies I turn to Amazon because they have a great range of supplies, in one place, that's easy to navigate, and I am able to find what I need with ease. 

I am part of various affiliate programs including Amazon – when you click on an affiliate link and then go on to make a purchase, at no cost to you, I receive a small commission. 

I use the money raised towards the cost of running this blog. I hope if you like the content of my blog, you will support me by clicking through these links to make your purchases. 

Thank you!